Brandenburg Telephone Company

Welcome, this page is under construction. If you see something that doesn't look just right, we are working on it.

Thanks

Remote Control

SRC-200

Programming your SRC-200 Remote Control

If you are simply replacing a TV to be used with an existing remote and video steam, scroll down to the section labeled Programming Remote to a TV

Programming the Gateway ID

The Gateway ID should be labeled on the back of the remote control.

  • On remote: Push and hold “B” until red LED light flashes.
  • Press 7, 8, 9 and then enter the Gateway ID.

Programming to a Video Stream

  • Press and hold the A button until the lights start flashing.
  • Press 7, 8, 9 and press the stream number you wish to use. (Stream 1 = ch 3, Stream 2 - ch 7, Stream 3 = ch 13)

Programming Remote to a TV

Follow these instructions if you are replacing a TV:

  • Start with the TV turned on.
  • Press and hold the MUTE button until the light starts flashing.
  • Press and release the POWER button: The light will stop blinking and remain solid.
  • Press the ARROW UP button (between GUIDE & SELECT) repeatedly until the TV turns off.
  • Press the SELECT button.

SRC-300A

Programming your SRC-300A Remote Control.

If you are simply replacing a TV to be used with an existing remote and video stream, scroll down to the section labeled (947) 762-3118

Programming Gateway ID

The Gateway ID should be labeled on the back of the remote control. If you can not find this 3 digit code follow the next few steps.

  • Make sure TV is set to Stream 1's signal (ie: ch 3).
  • Push the "Menu" button of the Gateway front panel.
  • Scroll to "Remote Control Setup" using the UP and DOWN arrows on the gateway.
  • Press the "Select" button the on the Gateway front panel
  • Press the LED button on the remote and hold it down until the LED flashes rapidly.
  • Press the REC button. The LED stops blinking at this point and stays solid.
  • Press and release the B button.
  • Press in the code (ie: 187)

Programming Remote to a Video Stream

  • Press the LED button and hold it down until the LED flashes rapidly.
  • Press the REC button. The LED stops blinking at this point and stays solid.
  • Press and release the A button.
  • Press 1, 2 or 3. (Stream 1 = ch 3, Stream 2 = ch 7, steam 3 = ch 13)

Programming Remote to a TV

Follow these instructions if your are replacing a TV:

  • Press the LED button and hold it down until the LED Flashes.
  • Press the REC button. The LED stops blinking at this point and stays solid.
  • Press and release the POWER. The remote is now in TV Code Scan Programming Mode.
  • Press the UP ARROW (above SELECT) button to scan through all the TV codes. When you reach the correct TV code, the TV will automatically turn off.
  • Press the SELECT button to store the TV code. The LED flashes rapidly then stops, indicating code has been stored.

SRC-350B

Programming your SRC-350B Remote Control.

If you are simply replacing a TV to be used with an existing remote and video stream, scroll down to the section labeled Programming Remote to a TV.

Programming Gateway ID

  • Locate the remote that controls the TV in the room with the gateway.
  • Push the "Menu" button of the Gateway front panel.
  • On the remote press the down arrow, then press Select.
  • Press the PPV button and you should have an informational message on the screen with thesource code that the gateway requires. This should be a 3 digit number. Please write this down.
  • Press and hold the Secect button, then the mute button. Hold both buttons down together untill the LED button illuminates, then release both buttons.
  • Press and release the B key. The LED button temporarily turns off. Releasing the key causes the LED button to light up again. You can now set the correct Gateway ID.
  • Enter the three-digit code assigned to your Gateway.(i.e. 007)
  • The LED light will blink twice.

Programming Remote to a Video Stream

  • Press and hold the select button, then the mute button. Hold both buttons down together untilthe LED button illuminates, then release both buttons.
  • Pres and release the A key. the LED button temporarily turns off. Releasing the key causes the LED button to light up again. You can now set the remote control ID.
    1. Press 0 for Stream 1 (TV channel 3) if the gateway is not in the same room.
    2. Press 1 for Stream 1 (TV channel 3) if the gateway is NOT in the same room.
    3. Press 2 for Stream 2 (TV channel 7).
    4. Press 3 for Stream 3 (TV channel 13).
  • The LED button will blink three times and go out. The new Remote Control ID is stored in the device.

Programming Remote to a TV

Follow these instructions if your are replacing a TV:

  • With the TV turned on. Press the Select button, the the Mute button. Hold both down until the LED button lights up and stays on.
  • Press the Up button above Select continuously until the TV turns off
  • Once the TV turns off press the Mute button, then press Select.
  • The LED will flash 3 times to indicate the code has been stored.

ADB Remote

Programming your ADB Remote Control.

  • Turn on your television.
  • Press and release the TV button.
  • Enter 9 9 1 , the TV button will blink twice.
  • Aim the remote at the TV and press and release the Power button.
  • Press and release the CH+ slowly until the TV turns off.
  • Press the power button to turn the TV back on.
  • Press the RCU Setup button to store the code for the TV. The TV button will blink twice.
  • Press and release the STB button.
  • Press and hold the RCU Setup button until the TV button blinks twice.
  • Enter 9 9 5
  • Press and release the Power button
  • Press and release the TV button
  • Press and release the Power button
  • Press and release the STB button
  • Press and hold the RCU Setup button until the TV button blinks twice.